Harness

The False Belly Band feeds through the keepers of the girth and buckles onto the tug straps (on a single harness) or the Breastplate to Saddle fitt...

False Martingales are designed to keep the breastplate in place. It is fitted by attaching the stainless steel clip to the small dee at the center ...

This is a soft, padded girth, designed for the comfort of the horse. It features 25mm (1") stainless steel buckles and is made to suit Classic Harn...

These straps are designed to buckle into each end of the girth. They are used where a little bit more length is required. 25mm (1") wide, this mod...

These 25mm (1")straps are made to suit Classic harness saddles. They loop onto the saddle dee, and are designed to secure the shaft loops/tugs in p...

Made using high density foam, these removable pads are fully contoured to the horse's shape for greater comfort and performance.This model is a ...

6" CLEVIS, BLACK STEEL - 2 1/4" opening, 5/8" bolt 5" CLEVIS, BLACK STEEL - 2" opening, 1/2" bolt 4" CLEVIS BLACK STEEL - 2" opening, 1/2" bolt 3" ...

Half Sweeney, All Leather Collars #550 This collar is for normal farm work. It has a high quality, top grain, black leather back and rim. The black...

Connects both sides of horse collar to keep them in place  Classic solid brass Strap opening is 1-1/4"

 This Collar Fastener is designed to work with a 1.25" Strap.

Collar Pad Kit includes: Pad Clip, Pad Plate, and two rivets.

Collar Pad- Deerhair Filling Collar pads should be ordered two sizes larger than the collar.

Combination Snap Used on harnesses to attach breast strap and pole strap together for snapping onto a neck yoke Size denotes strap width snap will...

Breeching is essentially part of the braking system for the harness. It is fitted around the rear end of the horse. As the horse slows, it uses the...

LEATHER CRUPPER WITH FORKS - DRAFT SIZE - Plain. Brass or Stainless Steel hardware. Stuffed with flax seed.

LEATHER CRUPPER WITH FORKS - DRAFT SIZE - Spotted. Brass or Stainless Steel hardware. Stuffed with flax seed.

LEATHER CRUPPER WITH FORKS - DRAFT SIZE - Plain. Brass or Stainless Steel hardware. Folded leather.

LEATHER CRUPPER WITH FORKS - DRAFT SIZE - Spotted. Brass or Stainless Steel hardware. Folded leather.

Traces are what attach the horse to the vehicle. They are buckled into the end of the breastplate and attached at the other end to the carriage tre...

Traces are what attach the horse to the vehicle. They are buckled into the end of the breastplate and attached at the other end to the carriage tre...

Lightweight and easy to wash and clean, this pad is suitable for use under driving saddles and breastplates to protect the bearing surfaces of the ...

Lightweight and easy to wash and clean, this pad is designed to fit under the breastplate wither strap to offer protection and comfort to the horse...

Trace carry straps are used to prevent the traces from hanging too low, thus helping to prevent the horse from getting their leg over the trace. T...

EVENER PIN, 5/8"

BRITCHEN PAD 1" X 6" X 48" foam britchen pad covered with imitation fur. Velcro fastener.

Comes in Brass and Chrome

5 Hole, 3/4" opening, 6" long

Hame Bolt, 3"

 Bolt Type 2"

 Pulling, Bolt Type 2"

 Chain Style

A handy kit to keep in the tack room in case of mishaps. Packed in a handy zip-up carryall, the kit contains:- 2 mtr x 16mm Apollo 2 mtr x 19mm Ap...

The Hip Strap (shown in red on the diagram) supports the breeching. These are replacement straps, designed to suit the Classic Complete Breeching

The Hip Straps (shown in red on the diagram) support the breeching. These are replacement straps, designed to suit the ZGB Complete Breeching